SSC JE 2017 Notification Complete Details Previous Question Papers & Syllabus of Civil,Mechanical & Electrical

Name of the Organisation: Staff Selection Commission

Name of the post: Junior Engineer

Detail of the Posts & Age Limit:

OrganisationPostAge LimitMust not be born before
Central Water CommissionJunior Engineer (Civil)Upto 32 years 2-1-1986 
Central Water CommissionJunior Engineer (Mechanical)Upto 32 years 2-1-1986 
CPWDJunior Engineer (Civil)Upto 32 years 2-1-1986 
CPWDJunior Engineer (Electrical)Upto 32 years 2-1-1986 
Department of PostJunior Engineer (Civil)Upto 27 years 2-1-1991
MESJunior Engineer (Civil)Upto 30 years 2-1-1988
MESJunior Engineer (Electrical and Mechanical)Upto 30 years 2-1-1988
MESJunior Engineer (Quantity Surveying and Contract)Upto 27 years 2-1-1991
Farrakka Barrage (Project)Junior Engineer (Civil)Upto 30 years 2-1-1988
Farrakka Barrage (Project)Junior Engineer (Electrical)Upto 30 years 2-1-1988
Farrakka Barrage (Project)Junior Engineer (Mechanical)Upto 30 years 2-1-1988
Director General Border Roads OrganisationJunior Engineer (Civil)Upto 30 years 2-1-1988
Director General Border Roads OrganisationJunior Engineer (Electrical)Upto 30 years 2-1-1988
Director General Border Roads OrganisationJunior Engineer (Mechanical)Upto 30 years 2-1-1988
Central Water Power Research Station.Junior Engineer (Civil)Upto 30 years 2-1-1988
Central Water Power Research Station.Junior Engineer (Electrical/Mechanical)Upto 30 years 2-1-1988
Dte. Of Quality Assurance (Naval)Junior Engineer (Naval Quantity Assurance) – (Mechanical)Upto 30 years 2-1-1988
Dte. Of Quality Assurance (Naval)Junior Engineer (Naval Quantity Assurance)(Electrical)Upto 30 years 2-1-1988
National Technical Research OrganisationJunior Engineer (Civil)Upto 30 years 2-1-1988
National Technical,Research OrganisationJunior Engineer (Electrical)Upto 30 years 2-1-1988
National Technical,Research OrganisationJunior Engineer (Mechanical)Upto 30 years 2-1-1988

Salary: Rs.35400-112400/-

Official Notification:

Educational Qualification:

Post Name Educational Qualification
Junior Engineer (Civil), CPWD Diploma in Civil Engineering from a recognized University or Institute.
Junior Engineer(Electrical) CPWD Diploma in Electrical or Mechanical Engineering from a recognised University or Institute.
Junior Engineer (Civil), Department of Posts Three years Diploma or equivalent in Civil Engineering from an institution
recognized by the Central Government or State Government.
Junior Engineer (Civil),MES Degree in Civil Engineering from a recognised University,
I)Three years Diploma in Civil Engineering from a recognised Institute or University or Board; and,
II) Two years experience in Planning, Execution and Maintenance of Civil Engineering works.
Junior Engineer (Electrical & Mechanical), MES ,Degree in Electrical or Mechanical Engineering from a recognised University;
I) Three years diploma in Electrical or Mechanical Engineering from a recognised Institute or University or,Board; and
II) Two years experience in Planning, Execution and Maintenance of Electrical or Mechanical Engineering works.
Junior Engineer (Quantity Surveying & Contract), MES i)3 years Diploma in Civil engineering from a recognised institute/University/Board or equivalent;
ii) Passed Intermediate examination in Building and Quantity Surveying Sub Divisional -II of the institute of Surveyors (India).
Junior Engineer (Civil), Central Water Commission (CWC) Degree or Diploma in Civil Engineering from a recognised University or Institution
Junior Engineer (Mechanical) in Central Water,Commission (CWC) Degree or Diploma in Mechanical Engineering from a recognised University or Institution.
Junior Engineer (Civil) in Farrakka Barrage Project, Diploma in Civil Engineering from a recognised University or Institute
Junior Engineer (Mechanical), Farrakka Barrage Project Diploma in Mechanical Engineering from a recognised University or Institute.
Junior Engineer (Electrical), Farrakka Barrage Project. Diploma in Electrical Engineering from a recognised University or Institute.
Junior Engineer (Civil),Roads Organisation, Ministry of Defence Three years Diploma in civil engineering or equivalent from the recognised University or Institute.
Two years working experience in the field of civil construction in monitoring and executive of projects.
Junior Engineer (Electrical / Mechanical), Border Roads Organisation in Ministry of Defence Three years Diploma in Engineering (Electrical and Mechanical) from the recognised University or Institute.
Two years working experience in the field of Electrical / Mechanical Engineering
in a area of construction in monitoring and executive of projects.
Junior Engineer (Civil), Central Water Power Research Station. Diploma in Civil Engineering from a recognised University.
Junior Engineer (Electrical / Mechanical), Central Water Power Research Station Diploma in Electrical from a recognised University.
Junior Engineer(Mechanical) Dte of,Quality Assurance Naval Diploma in Mechanical Engineering from any recognised University/Institution; and
Two years experience in respective fields i.e.- Either,of the field assurance/quality control/ production/manufacturing
and testing of marine engineering propulsion system including turbines, power generation equipment, hydraulic system,
as conditioning/refrigeration, pumps values, gears,and gear trains, boilers, cranes/winches/load handling devices etc.
including knowledge of various standard and their interpretation.
Junior Engineer (Electrical),Dte of Quality Assurance Naval Diploma in Electrical Engineering from any recognised University / Institution; and
Two years experience in respective fields i.e.-,Either of the field assurance / quality control / production / manufacturing
and testing of switch gears, cables, converters, light and light fitting, motors, generators, drives and control systems,
airfield lighting equipment, Electronics / Radar / Radio / Telecommunication equipment,
electro hydraulic system, programmable logic controller based systems, printed circuit boards / instrumentation, software development and validation, network control system etc. including knowledge of various standard and their interpretation.
Junior Engineer (Civil),National Technical Research Organisation Diploma in Civil Engineering from recognised University/Institution.
Junior Engineer (Electrical)National Technical Research Organisation. Diploma in Electrical Engineering from recognised University/Institution.
Junior Engineer (Mechanical) National Technical Research Organisation Diploma in Mechanical Engineering from recognised University/Institution.

Scheme of Examination:

Subject Number of Questions Maximum Marks Duration Mode of Examination
General Intelligence & Reasoning 50 50 2 Hours
Morning Shift(10 A.M-12 Noon)
Afternoon Shift(2-4 PM)
Online Examination
General Awareness 50 50
Part.A General Engineering(Civil & Structural),OR
Part-B,General Engineering,(Electrical),OR
Part-C,General Engineering (Mechanical)
100 100

Subject Maximum Marks Duration Mode of Examintion
Part-A General,Engineering,(Civil & Structural),
Part- B General Engineering,(Electrical),
Part-C,General Engineering,(Mechanical)
300 2 hours Written Examination (Conventional)

Mode of Selection:
Those who qualify SSC JE Paper-1which is Objective will be eligible to Write the SSC JE Paper-2 which is Descriptive (Conventional Type).

Application Fee: Rs.100
Women candidates and candidates belonging to Scheduled Caste, Scheduled Tribe, Physically Handicapped and Ex-Servicemen (eligible for reservation) are exempted from paying application fee as per extant Government Orders.

Important Dates:
Application Start Date:21-10-2017
Last Date to Apply:17-11-2017
Date of Written Test( Paper-1):5-1-2018 to 8-1-2017 

Question Papers:

Click the below link for SSC JE 2013 Paper:
Click the below link for SSC JE 2014 Paper:

Click the below link for SSC JE 2015 Paper:

Click here for SSC JE Paper- 2 Mechanical conventional Paper:(2007-2013)

Cut-Off of SSC JE:

Branch Year UR OBC SC ST OH HH
Civil 2014 93.75 82 75.75 70 69 40
Electrical/Mechanical 2014 117.5 109.5 102.5 93.75 93 69
Civil 2015 103.75 91.25 88 87.75 78 30
Electrical/Mechanical 2015 131 125.25 115.5 105.5 100 80.5
Civil 2016 100 92.5 84.5 85.5 72.5 40
Electrical/Mechanical 2016 115 109.5 99 94.5 87 54

Syllabus for Paper-1:


(i) General Intelligence & Reasoning: 
The Syllabus for General Intelligence would include questions of both verbal and non-verbal type. The test may include questions on analogies, similarities, differences, space visualization, problem solving, analysis, judgement, decision making, visual memory, discrimination, observation, relationship concepts, arithmetical reasoning, verbal and figure classification, arithmetical number series etc. The test will also include questions designed to test the candidate’s abilities to deal with abstract ideas and symbols and their relationships, arithmetical computations and other analytical functions.

(ii) General Awareness: 
Questions will be aimed at testing the candidate’s general awareness of the environment around him/her and its application to society. Questions will also be designed to test knowledge of current events and of such matters of everyday observations and experience in their scientific aspect as may be expected of any educated person. The test will also include questions relating to India and its neighboring countries especially pertaining to History, Culture, Geography, Economic Scene, General Polity and Scientific Research, etc. These questions will be such that they do not require a special study of any discipline.
(iii) General Engineering (Civil and Structural), (Electrical & Mechanical):
Civil Engineering
Building Materials, Estimating, Costing and Valuation, Surveying, Soil Mechanics, Hydraulics, Irrigation Engineering, Transportation Engineering, Environmental Engineering.
Structural Engineering: Theory of Structures, Concrete Technology, RCC Design, Steel Design.
Electrical Engineering
Basic concepts, Circuit law, Magnetic Circuit, AC Fundamentals, Measurement and Measuring instruments, Electrical Machines, Fractional Kilowatt Motors and single phase induction Motors, Synchronous Machines, Generation, Transmission and Distribution, Estimation and Costing, Utilization and Electrical Energy, Basic Electronics.
Mechanical Engineering 
Theory of Machines and Machine Design, Engineering Mechanics and Strength of Materials,
Properties of Pure Substances, 1st Law of Thermodynamics, 2nd Law of Thermodynamics, Air standard Cycles for IC Engines, IC Engine Performance, IC Engines Combustion, IC Engine Cooling & Lubrication,  Rankine cycle of System, Boilers, Classification, Specification, Fitting & Accessories, Air Compressors & their cycles, Refrigeration cycles, Principle of Refrigeration Plant, Nozzles & Steam Turbines.  
Properties & Classification of Fluids, Fluid Statics, Measurement of Fluid Pressure, Fluid kinematics, Dynamics of Ideal fluids, Measurement of Flow rate, basic principles, Hydraulic Turbines, Centrifugal Pumps,  Classification of steels. 

Syllabus for Paper II:


(Part-A) :Civil & Structural Engineering

Building Materials :
Physical and Chemical properties, classification, standard tests, uses and manufacture/quarrying of materials e.g. building stones, silicate based materials, cement (Portland), asbestos products, timber and wood based products, laminates, bituminous materials, paints, varnishes.Estimating, Costing and Valuation: estimate, glossary of technical terms, analysis of rates, methods and unit of measurement, Items of work – earthwork, Brick work (Modular & Traditional bricks), RCC work, Shuttering, Timber work, Painting, Flooring, Plastering. Boundary wall, Brick building, Water Tank, Septic tank, Bar bending schedule, Centre line method, Mid-section formula, Trapezodial formula, Simpson’s rule. Cost estimate of Septic tank, flexible pavements, Tube well, isolates and combined footings, Steel Truss, Piles and pile-caps. Valuation – Value and cost, scrap value, salvage value, assessed value, sinking fund, depreciation and obsolescence, methods of valuation.
Surveying :
 Principles of surveying, measurement of distance, chain surveying, working of prismatic compass, compass traversing, bearings, local attraction, plane table surveying, theodolite traversing, adjustment of theodolite, Levelling, Definition of terms used in levelling, contouring, curvature and refraction corrections, temporary and permanent adjustments of dumpy level, methods of contouring, uses of contour map, tachometric survey, curve setting, earth work calculation, advanced surveying equipment.
Soil Mechanics : 
Origin of soil, phase diagram, Definitions-void ratio, porosity, degree of saturation, water content, specific gravity of soil grains, unit weights, density index and interrelationship of different parameters, Grain size distribution curves and their uses. Index properties of soils, Atterberg’s limits, ISI soil classification and plasticity chart. Permeability of soil, coefficient of permeability, determination of coefficient of permeability, Unconfined and confined aquifers, effective stress, quick sand, consolidation of soils, Principles of consolidation, degree of consolidation, pre-consolidation pressure, normally consolidated soil, e-log p curve, computation of ultimate settlement. Shear strength of soils, direct shear test, Vane shear test, Triaxial test. Soil compaction, Laboratory compaction test, Maximum dry density and optimum moisture content, earth pressure theories, active and passive earth pressures, Bearing capacity of soils, plate load test, standard penetration test.
Hydraulics : 
Fluid properties, hydrostatics, measurements of flow, Bernoulli’s theorem and its application, flow through pipes, flow in open channels, weirs, flumes, spillways, pumps and turbines.
Irrigation Engineering: Definition, necessity, benefits, 2II effects of irrigation, types and methods of irrigation, Hydrology – Measurement of rainfall, run off coefficient, rain gauge, losses from precipitation – evaporation, infiltration, etc. Water requirement of crops, duty, delta and base period, Kharif and Rabi Crops, Command area, Time factor, Crop ratio, Overlap allowance, Irrigation efficiencies. Different type of canals, types of canal irrigation, loss of water in canals. Canal lining – types and advantages. Shallow and deep to wells, yield from a well. Weir and barrage, Failure of weirs and permeable foundation, Slit and Scour, Kennedy’s theory of critical velocity. Lacey’s theory of uniform flow. Definition of flood, causes and effects, methods of flood control, water logging, preventive measure. Land reclamation, Characteristics of affecting fertility of soils, purposes, methods, description of land and reclamation processes. Major irrigation projects in India.
Transportation Engineering: Highway Engineering – cross sectional elements, geometric design, types of pavements, pavement materials – aggregates and bitumen, different tests, Design of flexible and rigid pavements – Water Bound Macadam (WBM) and Wet Mix Macadam (WMM), Gravel Road, Bituminous construction, Rigid pavement joint, pavement maintenance, Highway drainage, Railway Engineering- Components of permanent way – sleepers, ballast, fixtures and fastening, track geometry, points and crossings, track junction, stations and yards. Traffic Engineering – Different traffic survey, speed-flow-density and their interrelationships, intersections and interchanges, traffic signals, traffic operation, traffic signs and markings, road safety.
Environmental Engineering: 
Quality of water, source of water supply, purification of water, distribution of water, need of sanitation, sewerage systems, circular sewer, oval sewer, sewer appurtenances, sewage treatments. Surface water drainage. Solid waste management – types, effects, engineered management system. 
Air pollution – pollutants, causes, effects, control. Noise pollution – cause, health effects, control.
Structural EngineeringTheory of structures: 
Elasticity constants, types of beams – determinate and indeterminate, bending moment and shear force diagrams of simply supported, cantilever and over hanging beams. Moment of area and moment of inertia for rectangular & circular sections, bending moment and shear stress for tee, channel and compound sections, chimneys, dams and retaining walls, eccentric loads, slope deflection of simply supported and cantilever beams, critical load and columns, Torsion of circular section.
Concrete Technology: 
Properties, Advantages and uses of concrete, cement aggregates, importance of water quality, water cement ratio, workability, mix design, storage, batching, mixing, placement, compaction, finishing and curing of concrete, quality control of concrete, hot weather and cold weather concreting, repair and maintenance of concrete structures.
RCC Design: 
RCC beams-flexural strength, shear strength, bond strength, design of singly reinforced and double reinforced beams, cantilever beams. T-beams, lintels. One way and two way slabs, isolated footings. Reinforced brick works, columns, staircases, retaining wall, water tanks (RCC design questions may be based on both Limit State and Working Stress methods).
Steel Design: Steel design and construction of steel columns, beams roof trusses plate girders.

Part-B (Electrical Engineering):

Basic concepts : 
Concepts of resistance, inductance, capacitance, and various factors affecting them. Concepts of current, voltage, power, energy and their units.
Circuit law : 
Kirchhoff’s law, Simple Circuit solution using network theorems.
Magnetic Circuit : 
Concepts of flux, mmf, reluctance, Different kinds of magnetic materials, Magnetic calculations for conductors of different configuration e.g. straight, circular, solenoidal, etc. Electromagnetic induction, self and mutual induction.
AC Fundamentals:
 Instantaneous, peak, R.M.S. and average values of alternating waves, Representation of sinusoidal wave form, simple series and parallel AC Circuits consisting of R.L. and C, Resonance, Tank Circuit. Poly Phase system – star and delta connection, 3 phase power, DC and sinusoidal response of R-Land R-C circuit.
Measurement and measuring instruments:
 Measurement of power (1 phase and 3 phase, both active and re-active) and energy, 2 wattmeter method of 3 phase power measurement. Measurement of frequency and phase angle. Ammeter and voltmeter (both moving oil and moving iron type), extension of range wattmeter, Multimeters, Megger, Energy meter AC Bridges. Use of CRO, Signal Generator, CT, PT and their uses. Earth Fault detection.
Electrical Machines :
 (a) D.C. Machine – Construction, Basic Principles of D.C. motors and generators, their characteristics, speed control and starting of D.C. Motors. Method of braking motor, Losses and efficiency of D.C. Machines. (b) 1 phase and 3 phase transformers – Construction, Principles of operation, equivalent circuit, voltage regulation, O.C. and S.C. Tests, Losses and efficiency. Effect of voltage, frequency and wave form on losses. Parallel operation of 1 phase /3 phase transformers. Auto transformers. (c) 3 phase induction motors, rotating magnetic field, principle of operation, equivalent circuit, torque-speed characteristics, starting and speed control of 3 phase induction motors. Methods of braking, effect of voltage and frequency variation on torque speed characteristics.
Fractional Kilowatt Motors and Single Phase Induction Motors: Characteristics and applications.
Synchronous Machines - Generation of 3-phase e.m.f. armature reaction, voltage regulation, parallel operation of two alternators, synchronizing, control of active and reactive power. Starting and applications of synchronous motors.
Generation, Transmission and Distribution 
– Different types of power stations, Load factor, diversity factor, demand factor, cost of generation, inter-connection of power stations. Power factor improvement, various types of tariffs, types of faults, short circuit current for symmetrical faults. Switchgears – rating of circuit breakers, Principles of arc extinction by oil and air, H.R.C. Fuses, Protection against earth leakage / over current, etc. Buchholtz relay, Merz-Price system of protection of generators & transformers, protection of feeders and bus bars. Lightning arresters, various transmission and distribution system, comparison of conductor materials, efficiency of different system. Cable – Different type of cables, cable rating and derating factor.
Estimation and costing : Estimation of lighting scheme, electric installation of machines and relevant IE rules. Earthing practices and IE Rules.
Utilization of Electrical Energy : 
Illumination, Electric heating, Electric welding, Electroplating, Electric drives and motors.
Basic Electronics : 
Working of various electronic devices e.g. P N Junction diodes, Transistors (NPN and PNP type), BJT and JFET. Simple circuits using these devices.

Mechanical Engineering:

Theory of Machines and Machine Design  
Concept of simple machine, Four bar linkage and link motion, Flywheels and fluctuation of energy, Power transmission by belts – V-belts and Flat belts, Clutches – Plate and Conical clutch, Gears – Type of gears, gear profile and gear ratio calculation, Governors – Principles and classification, Riveted joint, Cams, Bearings, Friction in collars and pivots.   
Engineering Mechanics and Strength of Materials  
Equilibrium of Forces, Law of motion, Friction, Concepts of stress and strain, Elastic limit and elastic constants, Bending moments and shear force diagram, Stress in composite bars, Torsion of circular shafts, Bucking of columns – Euler‟s and Rankin‟s theories, Thin walled pressure vessels.  
Thermal Engineering   
Properties of Pure Substances : p-v & P-T diagrams of pure substance like H2O, Introduction of steam table with respect to steam generation process; definition of saturation, wet & superheated status.  Definition of dryness fraction of steam, degree of superheat of steam. H-s chart of steam (Mollier‟s Chart). 
1st Law of Thermodynamics: Definition of stored energy & internal energy, 1st Law of Thermodynamics of cyclic process, Non Flow Energy Equation, Flow Energy & Definition of Enthalpy, Conditions for Steady State Steady Flow; Steady State Steady Flow Energy Equation. 2nd Law of Thermodynamics : Definition of Sink, Source Reservoir of Heat, Heat Engine, Heat Pump & Refrigerator; Thermal Efficiency of Heat Engines & co-efficient of performance of Refrigerators, Kelvin – Planck & Clausius Statements of 2nd Law of Thermodynamics, Absolute or Thermodynamic Scale of temperature, Clausius Integral, Entropy, Entropy change calculation of ideal gas processes.   Carnot Cycle & Carnot Efficiency, PMM-2; definition & its impossibility.  
Air standard Cycles for IC engines : Otto cycle; plot on P-V, T-S Planes; Thermal Efficiency, Diesel Cycle; Plot on P-V, T-S planes; Thermal efficiency.  
IC Engine Performance, IC Engine Combustion, IC Engine Cooling & Lubrication. Rankine cycle of steam : Simple Rankine cycle plot on P-V, T-S, h-s planes, Rankine cycle efficiency with & without pump work.  
Boilers; Classification; Specification; Fittings & Accessories :
 Fire Tube & Water Tube Boilers.  Air Compressors & their cycles; Refrigeration cycles; Principle of a Refrigeraton Plant; Nozzles & Steam Turbines   
Fluid Mechanics & Machinery 
Properties & Classification of Fluid :  ideal & real fluids, Newton‟s law of viscosity, Newtonian and Non-Newtonian fluids, compressible and incompressible fluids.  Fluid Statics: Pressure at a point.  Measurement of Fluid Pressure: Manometers, U-tube, Inclined tube.   
Fluid Kinematics: Stream line, laminar & turbulent flow, external & internal flow, continuity equation.  Dynamics of ideal fluids: Bernoulli‟s equation, Total head; Velocity head; Pressure head; Application of Bernoullis equation.    
Measurement of Flow rate Basic Principles: Venturimeter, Pilot tube, Orifice meter.    
Hydraulic Turbines: Classifications, Principles.  
Centrifugal Pumps: Classifications, Principles, Performance.  
Production Engineering 
Classification of Steels : mild steal & alloy steel, Heat treatment of steel, Welding – Arc Welding, Gas Welding, Resistance Welding, Special Welding Techniques i.e. TIG, MIG, etc. (Brazing & Soldering), Welding Defects & Testing; NDT, Foundry & Casting – methods, defects, different casting processes, Forging, Extrusion, etc, Metal cutting principles, cutting tools, Basic Principles of machining with (i) Lathe (ii) Milling (iii) Drilling (iv) Shaping (v) Grinding, Machines, tools & manufacturing processes. 

Official Notification:


Popular posts from this blog

NIT Calicut Recruitment 2022 Non Faculty

DRDO Technician-A Recruitment 2022

upsrtc vacancy 2022 - conductor, driver, new vacancy, recruitment apply online